Posts: 839
Threads: 0
Joined: Jun 2007
I'm normally in the lathe forum but my question is about an old Stanley plane.
I want to do some inlay before I turn some pieces. My plan is to make my cut with the bandsaw and put in a contrasting wood. How do I set the plane for a deeper cut for a thicker ribbon. I have moved the knob but see no difference. I get nice ribbons now but they are thinner than I want in the pieces I have tried it on.
Thanks.
Posts: 22,711
Threads: 0
Joined: Feb 2005
Location: Regina Saskatchewan Canada
The thickness of shaving you can cut will depend on a lot of things but the wood is going to be the major one. You may have noticed that the shavings want to curl. A thick shaving is going to break before it will curl that tight. My suggestion, forget the plane and cut strips on the tablesaw.
Blackhat
Bad experiences come from poor decisions. So do good stories.
Posts: 19,999
Threads: 0
Joined: Jul 2003
You might try cutting as thin a piece of inlay as possible on a tablesaw or bandsaw then glue that in place and plane it down to match.
carl
Posts: 6,562
Threads: 2
Joined: Sep 2006
Location: North Florida
The purpose of your plane is to make wood thinner and shavings are a byproduct. I doubt you will be successful making a suitable thick shaving because the force of cutting breaks the wood fibers of the shaving.
There is a way to use your plane to produce the thin wood you require. First, use your bandsaw to create a thin piece of wood. Then use your plane to make this thin piece thinner.
Good luck with your project.
===---===---===---===---===---===---===---===---
Please visit my website
splintermaking.com
Posts: 13,412
Threads: 4
Joined: Jun 2007
Location: New Jersey
What Jim said.
Credo Elvem ipsum etiam vivere
Non impediti ratione cogitationis
Posts: 14,851
Threads: 10
Joined: Jan 2010
Location: southeastern VA
I have not seem Alex around here in quite a while, but you might want to check out his inlay cutting technique (~1:35)
Pens 4 College A zero-clearance insert on the TS would have been a good idea.
FWIW
"the most important safety feature on any tool is the one between your ears." - Ken Vick
A wish for you all: May you keep buying green bananas.
Posts: 839
Threads: 0
Joined: Jun 2007
Thanks for the answers. I inlay pen blanks and peppermill blanks from simple cross and angle cuts to swirl designs. I am taking the edge off of a one and a quarter inch wide board of contrasting color with the plane. I soak the curl for roughly ten minutes while I put glue in the cuts then thread the curl into the cut and clamp. Longest I have needed so far is only 2 four inch long pieces in a peppermill swirled pattern. Not worried about the filling the center since it is drilled out.
Using the table saw to make the pieces makes a lot of sawdust for what I want to do and I have had good results with the pieces off the plane.. I want my curls a little thicker on some pieces so I can show more of the contrast.
Posts: 352
Threads: 0
Joined: Sep 2006
Well, if you want to go the plane route (I assume you've already tried veneer). You might try backing off the chip-breaker (maybe to a 16th or more) and setting the frog back so you get an open mouth. Choose straight grained wood and have at it. Good luck!
Posts: 116
Threads: 0
Joined: Mar 2013
Veneer is sliced in production, essentially the same way as the plane will cut. Don't know what is cutting angle of giant knife that slice it, but I believe it is in proximity of plane angle.
Is I remember log is soaked before slicing.
Never tried, but it cross my mind that you can try to put some veneer softener to board before you cut it.
