Posts: 4,157
Threads: 2
Joined: Feb 2003
Location: Winston Salem, NC
I have a picture in my mind for a shop cabinet. Got the 3/4 Ply and drawer glides so I'm getting to the point of cutting some stock.
This will be a 5 drawer cabinet with the outside dimensions of the box itself being 32" wide X 24" deep X 24" high and will have 3" casters installed. The box itself will be made from 3/4" plywood - what should I consider using for the back - is 1/4" ply enough or should I go to 1/2". The expected weight of the contents will be fairly light - probably the heaviest things will be a 10" and 8" dado set in one drawer.
Thanks
Rick
Posts: 2,721
Threads: 0
Joined: Feb 2002
While the construction likely doesn't necessitate 1/2" ply I would use because of the mobile usage this cabinet will see. Presuming the casters are to make it mobile.
The first time I wheeled it around the shop I'd back it into something sharp enough to gouge the 1/4" ply, perhaps even hard enough to puncture it.
~Dan.
Posts: 29,152
Threads: 1
Joined: Aug 2002
1/4" is fine the back is there more to keep the dust out and prevent the case from racking.
Joe
Let us not seek the Republican Answer , or the Democratic answer. Let us not seek to fix the blame for the past. Let us accept our own responsibility for the future John F. Kennedy
Posts: 2,274
Threads: 90
Joined: Jun 2001
I'd go with 1/2" only because I hang things from a couple of my cabinets and the 1/2" makes it easier to attach thing to it.
John
Always use the right tool for the job.
We need to clean house.
Posts: 20,381
Threads: 4
Joined: Sep 2007
Location: CinDay
1/4" will do just fine.
Worst thing they can do is cook ya and eat ya
GW
Posts: 4,157
Threads: 2
Joined: Feb 2003
Location: Winston Salem, NC
Thanks guys - I'll probably go with with 1/4" although I understand and agree with the points for 1/2". Based on the anticipated usage of the cabinet I think 1/4" will serve the purpose.
Thanks
Rick
Posts: 965
Threads: 0
Joined: May 2004
Will the "box" have a bottom? If the box is 3/4 all the way around with a captured back in a groove, glued in since it is plywood, then yes 1/4 will be sufficient for the back.
I did mine with 3/4 all the way around, plus a 3/4 back. My reason was that I made hinged wings in both sides to give me more working area. The wings had fold out supports from their bottoms to about 1/2 way up on the sides of the cabinet. I didn't want the weight of those supports to squeeze the sides to the point that the drawers wouldn't work.
The other reason was that I wanted to be able to attach places to store tools to the back. Little used carpenters squares, clamps, etc and the 3/4 back provided the support structure for that.
Posts: 4,157
Threads: 2
Joined: Feb 2003
Location: Winston Salem, NC
the box will be 3/4" ply on all sides. I'm wondering why you are suggesting gluing in a 1/4" ply back - I wasn't planning on doing that but certainly could. My plan was to float it?
Thanks
Rick
Posts: 29,152
Threads: 1
Joined: Aug 2002
I have a 3/4" cabinet loaded to the gills ( three drawers) that is probably in the 350# range loaded
it is frameless cabinet with a stapled on 1/4" melamine over mdf back.
It has never moved or bowed the sides......
Joe
Let us not seek the Republican Answer , or the Democratic answer. Let us not seek to fix the blame for the past. Let us accept our own responsibility for the future John F. Kennedy
Posts: 2,721
Threads: 0
Joined: Feb 2002
Quote:
the box will be 3/4" ply on all sides. I'm wondering why you are suggesting gluing in a 1/4" ply back - I wasn't planning on doing that but certainly could. My plan was to float it?
I don't think it was so much a recommendation as a statement regarding plywood's tendency to be unmoving as opposed to solid wood. In other words, glueing the ply will not contribute to joint failure due to wood movement.
Floating the ply in a groove is fine; no reason to actually glue it.
~Dan.
