Posts: 381
Threads: 0
Joined: Jun 2002
A few years ago, I built a mobile air filtration device from an old HVAC blower. Would a dryer motor do the same thing on a smaller scale? This one is sitting in my garage. It's 1/3 hp, 6.4 amps, 120v, 1725 RPM. Thanks for any thoughts. --Rich
![[Image: 20160918_181103.jpg]](http://i1094.photobucket.com/albums/i445/Rich42198/20160918_181103.jpg)
[/img]
Posts: 31
Threads: 0
Joined: Jun 2012
That's a pretty small motor to move much air.
Doing it right cost less than doing it over
Posts: 12,901
Threads: 0
Joined: Jan 2010
Location: Lewiston, NY
Welcome TexasWally.
I used a fan/motor about that size for the shop built HEPA filter I built and it works just fine.
John
Posts: 5,733
Threads: 2
Joined: Dec 2004
Location: Fort Worth
Not a bad idea for an airfilter motor as dryers move more air than most commercially made shop aircleaners. They even push air at a decent pressure because they have duct runs to push the air down.
Posts: 16,604
Threads: 0
Joined: Oct 2002
Location: Ra-cha-cha, NY
Agree that it's too small for a dust collector, but just about right for an air filter.
Do measure the current draw against the nameplate value. Without ductwork, and with clean filters, it may move too much air and therefore draw too much current, resulting in shortened life. Potentially very short.
Tom
“This place smells like that odd combination of flop sweat, hopelessness, aaaand feet"
Posts: 13,412
Threads: 0
Joined: Jun 2004
Location: Texas
They can do upwards of 200 cfm- don't know the available static. It might be good for a sanding table.
Posts: 381
Threads: 0
Joined: Jun 2002
I don't have a wiring diagram for the motor. Is black hot, red neutral and the yellow and orange to be ignored?
Posts: 20,381
Threads: 4
Joined: Sep 2007
Location: CinDay
09-24-2016, 09:14 AM
(This post was last modified: 09-24-2016, 09:16 AM by Steve N.)
I've got a furnace fan, with a 1/2, or 3/4 hp motor, forget the exact size. It came with a cobbled together DC unit the guy who owned my current 15" planer had made. He had passed, and the deal I made with his Daughter was I take the POS DC out of her hair, and then we did my deal on the planer. The actual box is plenty tight so that isn't the problem, but it would hardly suck at all. I've since burned the box, but still have the furnace fan, and the motor.
If someone local wants it to try to make this, it's free for the asking
(09-19-2016, 10:49 AM)daddo Wrote: They can do upwards of 200 cfm- don't know the available static. It might be good for a sanding table.
Thinking that is about all they could do. Gave it some thought, NAH
still would take up space, and not come close to earning it's keep
Worst thing they can do is cook ya and eat ya
GW
Posts: 1
Threads: 0
Joined: Jul 2021
07-12-2021, 01:05 PM
(This post was last modified: 07-12-2021, 01:56 PM by barnowl.)
what year of production is the motor?
Watching this one....
Posts: 16,604
Threads: 0
Joined: Oct 2002
Location: Ra-cha-cha, NY
07-12-2021, 01:48 PM
(This post was last modified: 07-12-2021, 01:49 PM by TDKPE.)
Uh, oh - another spam placeholder. Here comes the banhammer.
Tom
“This place smells like that odd combination of flop sweat, hopelessness, aaaand feet"
