Posts: 7,964
Threads: 0
Joined: Feb 2006
11-01-2017, 03:44 PM
I want to build a blanket chest for my granddaughter as a wedding present. I want it to have a chance to become a family heirloom.
I've found a plan I believe I can handle except I'm not sure about how to do 5/8" wide box joints on a board about 15" wide and 38 inches long.
My Porter-Cable jig is limited to 1/2 inch box joints and 12" width.
I believe I understand how to make a relatively simple jig for my table saw and the cutting process. I'd go for a fairly tall fence for the miter gauge.
Is it reasonable to attempt such a process with a board that size? If not or I've missed a better way, I'd like suggestions.
Phydeaux
Posts: 20,381
Threads: 4
Joined: Sep 2007
Location: CinDay
(11-01-2017, 03:44 PM)Phydeaux Wrote: I want to build a blanket chest for my granddaughter as a wedding present. I want it to have a chance to become a family heirloom.
I've found a plan I believe I can handle except I'm not sure about how to do 5/8" wide box joints on a board about 15" wide and 38 inches long.
My Porter-Cable jig is limited to 1/2 inch box joints and 12" width.
I believe I understand how to make a relatively simple jig for my table saw and the cutting process. I'd go for a fairly tall fence for the miter gauge.
Is it reasonable to attempt such a process with a board that size? If not or I've missed a better way, I'd like suggestions.
Sent you a PM.
Worst thing they can do is cook ya and eat ya
GW
Posts: 20,950
Threads: 0
Joined: May 2005
(11-01-2017, 03:44 PM)Phydeaux Wrote: I want to build a blanket chest for my granddaughter as a wedding present. I want it to have a chance to become a family heirloom.
I've found a plan I believe I can handle except I'm not sure about how to do 5/8" wide box joints on a board about 15" wide and 38 inches long.
My Porter-Cable jig is limited to 1/2 inch box joints and 12" width.
I believe I understand how to make a relatively simple jig for my table saw and the cutting process. I'd go for a fairly tall fence for the miter gauge.
Is it reasonable to attempt such a process with a board that size? If not or I've missed a better way, I'd like suggestions.
Try this router jig.
https://www.routerworkshop.com/boxjoints.html Make to suit, and make your pusher "sled" leg and upright large enough to handle longer stock.
No frustration from dado sets that won't cut a flat bottom, either!
Better to follow the leader than the pack. Less to step in.
Posts: 1,407
Threads: 2
Joined: Jun 2003
Yeah, you can do it they way you're thinking.
Posts: 20,381
Threads: 4
Joined: Sep 2007
Location: CinDay
I think bringing the tool to a big board is smarter than trying to bring a big board to the tool. A fella could get hurt.
Was Bob able to give you any help?
Worst thing they can do is cook ya and eat ya
GW
Posts: 2,840
Threads: 0
Joined: Nov 2006
Location: Western NY
11-08-2017, 05:41 PM
(This post was last modified: 11-08-2017, 06:04 PM by Cecil.)
(11-01-2017, 03:44 PM)Phydeaux Wrote: I want to build a blanket chest for my granddaughter as a wedding present. I want it to have a chance to become a family heirloom.
I've found a plan I believe I can handle except I'm not sure about how to do 5/8" wide box joints on a board about 15" wide and 38 inches long.
My Porter-Cable jig is limited to 1/2 inch box joints and 12" width.
I believe I understand how to make a relatively simple jig for my table saw and the cutting process. I'd go for a fairly tall fence for the miter gauge.
Is it reasonable to attempt such a process with a board that size? If not or I've missed a better way, I'd like suggestions.
Plans from the sponsor of these very forums!
I built one and use it a lot. The fingers can be equally sized, or not. I just need to ensure the minimum finger spacing is at least 1/2", since I am using a 1/2" top bearing bit.
Also, when I do a long piece, so I lay the jig on its side and put the work on top. I have to use a spacer on the bench to prop up the opposite end of the board.
Plans here
https://www.woodsmithplans.com/plan/finger-joint-jig/
I tried not believing. That did not work, so now I just believe
Posts: 7,902
Threads: 0
Joined: Jan 2007
The box joint is more utilitarian and not appropriate for a nice blanket chest. You don't see nice antiques with box joints, always dovetails. I have used them on a nice toolbox but it doesn't sit in the bedroom.
RD
------------------------------------------------------------------
"Boy could I have used those pocket screws!" ---Duncan Phyfe
Posts: 2,879
Threads: 0
Joined: Mar 2010
11-09-2017, 10:26 AM
(This post was last modified: 11-09-2017, 10:27 AM by TucsonLawrence.)
Maybe ask your local ww'ers club/guild if anyone has a Leigh or porter cable jig you can borrow? I lent mine out recently and it came back with a new dovetail bit and a nice piece of madrona :
and more importantly I made a new woodworking friend)
Posts: 20,381
Threads: 4
Joined: Sep 2007
Location: CinDay
I think they make a very nice look on cases, and that most recipients wouldn't know the difference between DT's or Box Joints.
Worst thing they can do is cook ya and eat ya
GW
Posts: 7,964
Threads: 0
Joined: Feb 2006
(11-09-2017, 05:08 PM)Steve N Wrote: I think they make a very nice look on cases, and that most recipients wouldn't know the difference between DT's or Box Joints.
That's the chest I'm working on. I didn't get around to capturing a picture for here. Thanks, Steve N.
Phydeaux