Woodnet Forums › › Active › Tool Swap N' Sell v
Need some Cork for carving tools
Thread Modes
Need some Cork for carving tools
Arlin Eastman Offline
Honored Veteran Brnz Md w/ValorPrplHrtx2
Posts: 21,259
Threads: 2
Joined: Mar 2009
Location: IA
#10
01-09-2020, 10:30 PM
We need about 40 - 60 of them so we can put the carving chisels into them to protect the sharp ends.

Can pay shipping Thanks  Just PM me for address
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification.  Thank You Everyone.

It is always the right time, to do the right thing.
Find
Reply
sniper Offline
Pirate from way back
Posts: 22,408
Threads: 0
Joined: Dec 2004
Location: Monrovia, AL
#11
01-10-2020, 07:42 AM (This post was last modified: 01-10-2020, 07:42 AM by sniper.)
(01-09-2020, 10:30 PM)Arlin Eastman Wrote: We need about 40 - 60 of them so we can put the carving chisels into them to protect the sharp ends.

Can pay shipping Thanks  Just PM me for address

If y'all don't drink wine (I'm guessing you don't), check the local restaurant(s) that serve wine and ask if they could save the corks for you. Just a thought.
Find
Reply
Arlin Eastman Offline
Honored Veteran Brnz Md w/ValorPrplHrtx2
Posts: 21,259
Threads: 2
Joined: Mar 2009
Location: IA
#12
01-10-2020, 02:44 PM
Thanks Bill in handtools said the same thing and I will call a few places to see who serves it.
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification.  Thank You Everyone.

It is always the right time, to do the right thing.
Find
Reply
Ohio Mike Offline
Member
Posts: 3,156
Threads: 1
Joined: Jan 2005
Location: Northern Ohio
#13
01-10-2020, 06:28 PM
(01-09-2020, 10:30 PM)Arlin Eastman Wrote: We need about 40 - 60 of them so we can put the carving chisels into them to protect the sharp ends.

Can pay shipping Thanks  Just PM me for address

I've been using scraps of rigid foam insulation.  Works great!

[Image: 49363837938_df7bd5c442_c.jpg]
Find
Reply
Arlin Eastman Offline
Honored Veteran Brnz Md w/ValorPrplHrtx2
Posts: 21,259
Threads: 2
Joined: Mar 2009
Location: IA
#14
01-11-2020, 01:02 PM
(01-10-2020, 06:28 PM)Ohio Mike Wrote: I've been using scraps of rigid foam insulation.  Works great!

[Image: 49363837938_df7bd5c442_c.jpg]

Thanks Mike.  How firmly do they hold the blade?
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification.  Thank You Everyone.

It is always the right time, to do the right thing.
Find
Reply
Ohio Mike Offline
Member
Posts: 3,156
Threads: 1
Joined: Jan 2005
Location: Northern Ohio
#15
01-11-2020, 02:17 PM
They hold very well.

I make sure to put them on the tool in the same orientation each time. That way I'm not cutting a second slot in the foam.

I imagine the same rule applies to cork as well.

Mike
Find
Reply
Timberwolf Offline
Honored Veteran
Posts: 116,087
Threads: 0
Joined: Jun 2002
Location: Sparkling Clearwater, Fl. Tampa Bay Area
#16
01-12-2020, 11:02 AM (This post was last modified: 01-12-2020, 11:04 AM by Timberwolf.)
(01-11-2020, 02:17 PM)Ohio Mike Wrote: They hold very well.

I make sure to put them on the tool in the same orientation each time.  That way I'm not cutting a second slot in the foam.  

I imagine the same rule applies to cork as well.

Mike

..........................
Too many knives to worry about
Crazy  
Big Grin

[Image: fullsizeoutput-ad7.jpg]

[Image: fullsizeoutput-ad6.jpg]
Often Tested.    Always Faithful.      Brothers Forever

Jack Edgar, Sgt. U.S. Marines, Korea, America's Forgotten War
Get off my lawn !
Upset





Find
Reply
Ohio Mike Offline
Member
Posts: 3,156
Threads: 1
Joined: Jan 2005
Location: Northern Ohio
#17
01-12-2020, 12:11 PM
(01-12-2020, 11:02 AM)Timberwolf Wrote: ..........................
Too many knives to worry about
Crazy  
Big Grin

That's impressive.  You would need a full sheet of rigid foam to make sheaths for all those tools!  
Laugh
Laugh
Find
Reply
Arlin Eastman Offline
Honored Veteran Brnz Md w/ValorPrplHrtx2
Posts: 21,259
Threads: 2
Joined: Mar 2009
Location: IA
#18
01-12-2020, 02:59 PM
[attachment=22879]
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification.  Thank You Everyone.

It is always the right time, to do the right thing.
Find
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.