Woodnet Forums › › Active › Woodturning v
Just found a tool that may help us with turning

▼
Arlin Eastman Offline
Honored Veteran Brnz Md w/ValorPrplHrtx2
Posts: 21,259
Threads: 2
Joined: Mar 2009
Location: IA
#7
03-26-2018, 08:03 PM
It is an off set Taper Metal Turning Attachment in 3MT Shank for Off-setting Lathe's Tailstock.

https://www.amazon.com/dp/B06X6CY9VV/ref...rd_w=Dywrp 


If you do a lot of off set work this may help.  I am thinking of getting it in the future.

What do you think?
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification.  Thank You Everyone.

It is always the right time, to do the right thing.
Find
Reply
▼
Timberwolf Offline
Honored Veteran
Posts: 116,078
Threads: 0
Joined: Jun 2002
Location: Sparkling Clearwater, Fl. Tampa Bay Area
#8
03-26-2018, 09:14 PM
(03-26-2018, 08:03 PM)Arlin Eastman Wrote: It is an off set Taper Metal Turning Attachment in 3MT Shank for Off-setting Lathe's Tailstock.

https://www.amazon.com/dp/B06X6CY9VV/ref...rd_w=Dywrp 


If you do a lot of off set work this may help.  I am thinking of getting it in the future.

What do you think?
,,,,,,,,
Looks like it has a #3 Morse taper, Arlin...What size does your lathe have? My wood lathes have a #2 in both headstock and tailstock...My metal lathes have #3 Morse in the headstock..
Often Tested.    Always Faithful.      Brothers Forever

Jack Edgar, Sgt. U.S. Marines, Korea, America's Forgotten War
Get off my lawn !
Upset





Find
Reply
Woodshop Offline
Double uke winner
Posts: 5,421
Threads: 0
Joined: Jun 2001
Location: Troy IL
#9
03-27-2018, 08:56 AM (This post was last modified: 03-27-2018, 09:01 AM by Woodshop.)
(03-26-2018, 08:03 PM)Arlin Eastman Wrote: It is an off set Taper Metal Turning Attachment in 3MT Shank for Off-setting Lathe's Tailstock.

https://www.amazon.com/dp/B06X6CY9VV/ref...rd_w=Dywrp 


If you do a lot of off set work this may help.  I am thinking of getting it in the future.

What do you think?



It only helps if you have a carriage to run your tool bits. Then you get a long taper.
You can do the same with a wood lathe by putting a stop on the turning tool and angle the tool rest . much easier
Life is what you make of it, change your thinking, change your life!
Don's woodshop
Website Find
Reply
▼
Arlin Eastman Offline
Honored Veteran Brnz Md w/ValorPrplHrtx2
Posts: 21,259
Threads: 2
Joined: Mar 2009
Location: IA
#10
03-27-2018, 11:43 AM
(03-27-2018, 08:56 AM)Woodshop Wrote: It only helps if you have a carriage to run your tool bits. Then you get a long taper.
You can do the same with a wood lathe by putting a stop on the turning tool and angle the tool rest . much easier

Don

I am not following your direction of thought.  Can you explain it in an easier way for me.
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification.  Thank You Everyone.

It is always the right time, to do the right thing.
Find
Reply
Thread Modes
Just found a tool that may help us with turning


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.