Woodnet Forums › › Active › Woodturning v
finally got lathe time

▼
PVW Offline
Member
Posts: 161
Threads: 0
Joined: Jul 2016
Location: Garrett Co. MD. 21550
#20
02-16-2020, 08:45 AM
curly silver maple and quilt. large bowl is 14 x 4
[attachment=24098]
Find
Reply
▼
SceneryMaker Offline
The Quiet Member
Posts: 4,434
Threads: 0
Joined: Oct 2008
Location: Central Indiana
#21
02-16-2020, 08:59 AM
Very pretty. I like the clean lines.
We do segmented turning, not because it is easy, but because it is hard.
Find
Reply
Turner52 Offline
Member
Posts: 917
Threads: 0
Joined: Sep 2008
#22
02-16-2020, 05:46 PM
That grain really pops. Great job
Find
Reply
Arlin Eastman Offline
Honored Veteran Brnz Md w/ValorPrplHrtx2
Posts: 21,259
Threads: 2
Joined: Mar 2009
Location: IA
#23
02-16-2020, 08:39 PM
That is some swell looking wood and the form looks great as well.  Thanks for showing.
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification.  Thank You Everyone.

It is always the right time, to do the right thing.
Find
Reply
FrankAtl Offline
Random doodad artist
Posts: 3,120
Threads: 0
Joined: Oct 2007
Location: Cumming, GA.
#24
02-18-2020, 08:50 AM
Beautiful work Mike. I love the quilted maple!
Find
Reply
med-one Offline
Member
Posts: 2,827
Threads: 2
Joined: Nov 2003
Location: S.E. Michigan
#25
02-20-2020, 11:19 AM
PVW,
How long did your bowl wood dry before your turned them?
Dave
Find
Reply
▼
PVW Offline
Member
Posts: 161
Threads: 0
Joined: Jul 2016
Location: Garrett Co. MD. 21550
#26
02-20-2020, 05:08 PM
(02-20-2020, 11:19 AM)med-one Wrote: PVW,
How long did your bowl wood dry before your turned them?
Dave

it varies. Year or more. I like to give them a minimum of 2 years .I have 5 in thick cherry slabs that have been cut and stickered for 7 years. I'd like to start turning some but the biggest ones are 20 wide and 8' long, and I just don't feel like man handling them right now .I like to turn dry wood for the most part. The silver maple has been in the shop for around 4 years. I have a 14 in green cherry burl blank that I hope to turn yet this week. I will also plan to use the Bartleys on it. Depends on how it feels
Find
Reply
MichaelMouse Offline
Member
Posts: 20,950
Threads: 0
Joined: May 2005
#27
02-24-2020, 12:19 PM
(02-20-2020, 11:19 AM)med-one Wrote: PVW,
How long did your bowl wood dry before your turned them?
Dave

Since it's been without comment for so long, I'll jump in with the standard TDT (Turn/Dry/Turn) recommendation.  Turn the piece to rough pattern, somewhere around 5/8 to 1" thickness, and take advantage of the fact that wood looses water through end grain 10 times as fast as face grain.  When you rough turn, be sure to round down to the bottom - no "dog dish" pattern- to minimize the face-grain dimension, thus split menace.   Continuous curve helps redirect drying stress as well.  

I'm a mortise hold guy, and lazy to boot, so I don't do weights and dates, I just measure mortise deformation to estimate readiness.  On almost any wood, a shrink of 1/8" across a 2" mortise means the piece is ready for re-turn. Depending on Relative Humidity and thickness, six weeks give or take. Gets the shelf space back to you a lot earlier than a year, risking deep checks.  10-12% cross-grain shrink should be fine even if you're a tenon guy.
Better to follow the leader than the pack. Less to step in.
Find
Reply
cbygeorge Offline
Member
Posts: 1,152
Threads: 1
Joined: Jun 2010
Location: South Central PA
#28
02-27-2020, 10:43 PM
Mike, nice to see you on here again!  Nice work!  Hope you and your better half are well.  Also hope to see you at Bedford this fall.  

Chuck
Find
Reply
▼
PVW Offline
Member
Posts: 161
Threads: 0
Joined: Jul 2016
Location: Garrett Co. MD. 21550
#29
02-28-2020, 07:13 AM
(02-27-2020, 10:43 PM)cbygeorge Wrote: Mike, nice to see you on here again!  Nice work!  Hope you and your better half are well.  Also hope to see you at Bedford this fall.  

Chuck

Hey Chuck. We missed you last fall at Bedford. Are you still carving?
Find
Reply
Thread Modes
finally got lathe time


Forum Jump:


Users browsing this thread: 1 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.