Posts: 2,384
Threads: 0
Joined: Jan 2008
Location: Irving, Tx
No experience with the kit. I do like the design, but my routers are heavy and I feel a little uneasy with 1-1/2" EMT for ten feet. On the other hand Lee Valley has a fine reputation.
"I tried being reasonable..........I didn't like it." Clint Eastwood
Posts: 18,478
Threads: 0
Joined: Jul 2006
Location: Milwaukee area
It is pretty clever if you ask me. And if I purchased that many white nylon spacers at my hardware store, they'd charge me $69 just for those!
Posts: 21,259
Threads: 2
Joined: Mar 2009
Location: IA
It does say out of stock until July 31st if you need it right now.
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification. Thank You Everyone.
It is always the right time, to do the right thing.
Posts: 24,145
Threads: 2
Joined: Sep 2003
Location: Missouri
(05-23-2020, 11:17 PM)OneStaple Wrote: Hey All,
I know this is a fairly new product (it's in the "what's new" section), but has anyone tried the new router sled from Lee Valley (linky)? I need to build a router sled to flatten a couple slabs and this looks like it could be a decent approach. It's not entirely DIY on building one (so saves time), but also not crazy expensive like some of the other pre-built options I've seen. I do worry that the 1-1/2" EMT might sag a little over a 10' length, but I also don't have a piece on hand to feel the stiffness.
Along similar lines, any thoughts on the quality of the flattening router bits (linky)? I know there are other options out there too.
Thanks,
Tyler
No advice on the kit, but that bit is what I use except it's a Whiteside brand bit.
Steve
Mo.
I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020
Posts: 2,382
Threads: 0
Joined: Dec 2011
One can cast doubt about the product as it's too new but anyone who wondered if its price is reasonable should find another (cheaper) hobby such as paper folding to do. $69 or more is how much many of us spend on a weekend family evening meal at a restaurant (pre covid 19). Non lavish by most people's standards. The fact that it has been sold out tells us perhaps it is underpriced.
Simon
Posts: 863
Threads: 0
Joined: Jan 2007
Location: Fairfax Station, VA
GeeDub Wrote:I played with some 1-1/2" EMT and the flex is pretty definite. These types of rigs are not designed to give you a ready-to-finish surface. I'm sure it does okay. It may be that a thicker wall pipe or a delicate touch would yield a more consistent surface. Obviously the closer you get to a flat surface off the rig, the less there is to do to get where you are going.
Understood that they're not ready-to-finish surfaces, but I don't want to have to wrestle a 1/4" dip out of the middle of the board when done with the router. Ideally some clean up with a hand plane, big planer, and/or big belt sander would get you essentially ready to finish. I'm wondering if I could jury rig some temporary/moveable mid-span supports to minimize deflection.
Stwood_ Wrote:No advice on the kit, but that bit is what I use except it's a Whiteside brand bit.
Are you saying that what Lee Valley sells is a Whiteside brand bit, or just that you use Whiteside's version of the same type of bit? I assume the latter.
Handplanesandmore Wrote:One can cast doubt about the product as it's too new but anyone who wondered if its price is reasonable should find another (cheaper) hobby such as paper folding to do.
I have no qualms with the pricing. I think it's pretty reasonable for the time it would save me, as long as the jig works reasonably well, as discussed.
Thanks for the thoughts all!
Tyler
