Posts: 21,259
Threads: 2
Joined: Mar 2009
Location: IA
Right now I have a very small Router Table 14x16 and it is Way to small to do anything with and I keep going off the edges and when I do that bad things happen.
What do I use and how would I make it? I was thinking 26" wide and 36" long but will wait to see what you guys think.
Arlin
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification. Thank You Everyone.
It is always the right time, to do the right thing.
Posts: 42,638
Threads: 0
Joined: Feb 2002
Well, down to basics, you can mount a router in just about any flat surface. Fences can be as simple as a board clamped onto the top. I would say I wouldn't go any bigger than the size you propose or even a bit smaller.
If you find the material you're using requires more space---that's a good time to switch over to hand routing. But as to long boards you're putting a profile on----you can always use roller or flip-top stands as in-feed and out feed supports.
Dave
Posts: 786
Threads: 0
Joined: Nov 2004
Mine is a Norm-esque design.
Top is 24" deep by 34" long. I've used it for everything from bookcases to pencil boxes and never found the size too small.
The only time it was "too small" was routing a bead detail on fascia boards for a shed, but the boards were 12 feet long. A roller stand and my then 12 year old provided infeed and outfeed support.
Mike
Posts: 21,259
Threads: 2
Joined: Mar 2009
Location: IA
I should say that the VA bought me the PC 3.5 hp router and the Jessum 2 router lift and I do have the Jessum protable router table that has the velco bag hooked on it.
I did not have another router until someone here I do not remember who sent me one of his 12 and it sure is a nice one too.
As in doing it by hand well some of the vets are in wheel chairs and some are just shaky like me so a table is our best bet.
I was thinking a good plywood but do not know what plywood is good for this nor strong enough and it has to be within my budget of $25 or less hopfully less.
I would also like to add a digital up and down thingy to so we can do better work and not hours of setting up since most of us do not have hours of setting up time.
Arlin
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification. Thank You Everyone.
It is always the right time, to do the right thing.
Posts: 21,259
Threads: 2
Joined: Mar 2009
Location: IA
Thanks Mike
We would NEVER do anything that big I am very sure of that since my garage is just a little bigger then that.
Arlin
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification. Thank You Everyone.
It is always the right time, to do the right thing.
Posts: 29,152
Threads: 1
Joined: Aug 2002
go to home Depot or Lowes and find a countertop
Works just fine and likely meets your budget
You may have to beef it up a little underneath but that is a minor issue Screws and glue will get you there
Let us not seek the Republican Answer , or the Democratic answer. Let us not seek to fix the blame for the past. Let us accept our own responsibility for the future John F. Kennedy
Posts: 21,259
Threads: 2
Joined: Mar 2009
Location: IA
That is a great idea and I know of someone that has some he is giving away.
Arlin
As of this time I am not teaching vets to turn. Also please do not send any items to me without prior notification. Thank You Everyone.
It is always the right time, to do the right thing.
Posts: 13,485
Threads: 0
Joined: Oct 1999
Arlin,
Check out the Plans Store page of my website. I have plans for a folding router table. It features an 18 by 32" top but folds away when you are not using it. I sell the plans, but will happily send you the PDF for free if you want to build one.
Folding Router Table Ralph
Posts: 6,755
Threads: 0
Joined: Aug 2001
Location: Post Falls, ID
Joe, nailed it, Arlin. Adding a piece of 3/4" mdf under a chunk of countertop will provide plenty of strength for that big PC router.
My table is 24" x 32" and I've had no need for anything bigger...
As for set-up time, I'll have something for you in a couple weeks...
Dave
"One should respect public opinion insofar as is necessary to avoid starvation and keep out of prison, but anything that goes beyond this is voluntary submission to an unnecessary tyrany, and is likely to interfere with happiness in all kinds of ways."
Posts: 1,430
Threads: 1
Joined: Jun 2008
Here is mine. 2, 3/4" sheets of MDF glued with Titebond III. 24"x36"
I used locating brad nails between the sheets to hold in place while drying. Snip the heads off.
http://s938.photobucket.com/user/MykRian...amp;page=1