Posts: 2,488
Threads: 0
Joined: Aug 2004
I purchased a
Oneway Wolverine Sharpening System 4 Piece Set and a CBN wheel. The only problem is that when I go to sharpen my gouge it keeps
kicking back and gives me grieve. Should the wheels turn top to bottom or is there a way to reverse the spin?
Jim
Posts: 1,616
Threads: 0
Joined: Feb 2010
Location: Coast of Maine
Wheels should turn top to bottom. I'm not very knowledgeable but have never experienced this. Can you post a pic with the gouge in place as though you are sharpening but without the grinder running?
g
I've only had one...in dog beers.
"You can see the stars and still not see the light"
The Eagles: Already Gone
Posts: 2,384
Threads: 0
Joined: Jan 2008
Location: Irving, Tx
Sounds like the wheel is off center.
"I tried being reasonable..........I didn't like it." Clint Eastwood
Posts: 2,488
Threads: 0
Joined: Aug 2004
(06-26-2021, 01:43 PM)Halfathumb Wrote: I purchased a Oneway Wolverine Sharpening System 4 Piece Set and a CBN wheel. The only problem is that when I go to sharpen my gouge it keeps
kicking back and gives me grieve. Should the wheels turn top to bottom or is there a way to reverse the spin?
Since I'm fairly new to WT a gentleman from my local WT club came over and straightened me out. I was trying trying to use the grinding jig w/o having the Vari-Grind accessory. He got me going the right way. He also helped me with some turning issues. He's quit patient with me.
He also showed me how to sharpen free hand until I get the accessory.
Jim
Posts: 20,950
Threads: 0
Joined: May 2005
(06-27-2021, 08:21 AM)Halfathumb Wrote: Since I'm fairly new to WT a gentleman from my local WT club came over and straightened me out. I was trying trying to use the grinding jig w/o having the Vari-Grind accessory. He got me going the right way. He also helped me with some turning issues. He's quit patient with me.
He also showed me how to sharpen free hand until I get the accessory.
That freehand technique he taught, using the existing contour/bevel as reference will remove less metal and get you a renewed edge faster, so you can get back to work. Diamond hones, and slips are even easier on that expensive metal but renew edges fine.
Save the pattern grinding for the few times you find something embedded which chips the tool.
Better to follow the leader than the pack. Less to step in.
Posts: 14,849
Threads: 10
Joined: Jan 2010
Location: southeastern VA
(06-26-2021, 01:43 PM)Halfathumb Wrote: I purchased a Oneway Wolverine Sharpening System 4 Piece Set and a CBN wheel. The only problem is that when I go to sharpen my gouge it keeps
kicking back and gives me grieve. Should the wheels turn top to bottom or is there a way to reverse the spin?
4-piece set is usually 2 bases, the V-arm, and the adjustable flat tool rest.
The V-arm without the fingernail jig is used for sharpening roughing gouges. You blacken the the bevel of the roughing gouge and then tweak in the v-arm so that it shows a clean strip the full height of the bevel. You do that with the grinder off and turning the wheel by hand.
If it is kicking back, only the sharp edge is touching the wheel (or the wheel is out of round as suggested above).
Also, the v-arm should not be used with 60grit wheels.
What grit wheel are you using? Did you use the necessary spacers to get the distance between the center of the grinder's axle and the v-arm?
"the most important safety feature on any tool is the one between your ears." - Ken Vick
A wish for you all: May you keep buying green bananas.
Posts: 1,616
Threads: 0
Joined: Feb 2010
Location: Coast of Maine
(06-27-2021, 08:21 AM)Halfathumb Wrote: Since I'm fairly new to WT a gentleman from my local WT club came over and straightened me out. I was trying trying to use the grinding jig w/o having the Vari-Grind accessory. He got me going the right way. He also helped me with some turning issues. He's quit patient with me.
He also showed me how to sharpen free hand until I get the accessory.
Jim,
You've found the best answer to your question. Your local club is an awesome resource!
g
I've only had one...in dog beers.
"You can see the stars and still not see the light"
The Eagles: Already Gone
