#17
Figured out my double router top problem. https://forums.woodnet.net/showthread.php?tid=7351048

Now if I could only figure out posting a photo (EDIT: fixd).
Reply

#18
Looks like a winning solution.  I'm guessing the fences are not shown as you mentioned them in the other thread.

For the pics, I find taking everything landscape works best.  The forum auto rotates for this format so portrait pics are sideways.
Reply
#19
That looks kinda costly....
Steve

Mo.



I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24


 
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020








Reply

#20
(06-30-2020, 11:02 AM)Stwood_ Wrote: That looks kinda costly....

It kinda was....

and that's not normally how I roll. But, this was incremental and the cost/ scope kinda got away from me. I honestly intended to put a CI router wing in my TS until I built a new single router top. I still wanted 2 routers in a table and after I got the first wing it hit me that I could put them back to back and have the double router table I always wanted. I just wanted to post because I've never seen this done and I thought I might be on to something. But you're right, I'll have more in this than I do my table saw when it's all done.

Fence is yet to come. I've got some 80/20 material that I intend to make a fence out of (80/20 also kinda costly).
Reply
#21
That came out great! I am sure you will enjoy using it.
Reply
#22
Looks good. Fully understand the cost kinda spiraling.......
Uhoh 

And also understand the tablesaw mounted router. I installed one in my griz after making a huge, right side ex table for it. Bought another new, Rockler plate and set it all up.
I think I used it once, and found it was in the way if I left it there.
Then the plate hole caught about every piece of sheet good I ran across the table. Made a insert to cover the hole, and I've never set a router in it again.
Steve

Mo.



I miss the days of using my dinghy with a girlfriend too. Zack Butler-4/18/24


 
The Revos apparently are designed to clamp railroad ties and pull together horrifically prepared joints
WaterlooMark 02/9/2020








Reply
#23
I did two bench dogs . I also bought 6 plates 6 routers and 3 door profiles I can swap out and go. I also have a shaper for raised panels, it's a business

[attachment=28010]
Life is what you make of it, change your thinking, change your life!
Don's woodshop
Reply

#24
(07-01-2020, 08:06 AM)Woodshop Wrote: I did two bench dogs . I also bought 6 plates 6 routers and 3 door profiles I can swap out and go. I also have a shaper for raised panels, it's a business
Well, so much for me taking credit for the idea to put 2 CI tops back to back. Nice rig you got. In hindsight, a wood cabinet would have been better for me. I thought I was saving time buying a prefab stand but with all the mods I had to do to get bolt holes to line up I think a cabinet would have been easier.
Reply
#25
Bet that thing weighs a ton!
I had one of those mounted to a shaper and used a power feed to handle both. It was a real nice system.
VH07V  
Reply

#26
the power feed is a wonderful thing on the benchdogs. 
Yes


I just put it all on a wood cabinet with locking casters.



[attachment=28125]
Life is what you make of it, change your thinking, change your life!
Don's woodshop
Reply
Double Router Top


Forum Jump:


Users browsing this thread: 2 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.