forstner bit set advise
#11
I'd like to get a nice set of forstner bits so looking for advise. I have a cheap set & a few others, but want a better set. I understand there are different rim types that have +'s & -'s.
Thanks
David
Reply
#12
How much are you going to use it?

I have a Porter Cable set that works very well for occasional use. The most common bit I use is 3/8" and I have replaced those with Freud bits four or five times. Every other one is fine.

This means that the Freud (and one Irwin) that I used as replacements lasted just as long as the PC. I use them to drill dowel holes in hardwoods frequently (especially when using dowels as plugs) because it produces a very clean hole.

All of my bits have been sawtooth or knife edge. I don't know that anything other than knife edge is used for the smaller diameter bits, but they both produce clean holes. I have never seen a wavy edge bit, but mine are old for the most part and I understand that's newer.
Reply
#13
(06-25-2018, 01:57 PM)DCM Wrote: I'd like to get a nice set of forstner bits so looking for advise. I have a cheap set & a few others, but want a better set. I understand there are different rim types that have +'s & -'s.
Thanks
David

I bought this same Freud carbide set well over 20 years ago for about $70, and they have been excellent; I only use them for furniture work.  Highly recommended. Price went up a bit though.....

https://www.amazon.com/Freud-Seven-Carbi...B0000225ZL
Credo Elvem ipsum etiam vivere
Non impediti ratione cogitationis
Reply
#14
Ditto that Freud carbide set. Mine must be about the same age as Admiral's since that's about what I paid. I've had them sharpened once over the years, but they do an exceptional job and don't seem to care if you drilling the rough stuff (like MDF, flake board, etc.). I will say this, I have a few Freud HSS forstner bits, and when new, they cut a much cleaner hole....but of course they don't stay that way nearly as long.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Reply
#15
I have the Freud FB-107 (not carbide); been using them for many years. No complaints at all.
Gary

Please don’t quote the trolls.
Liberty, Freedom and Individual Responsibility
Say what you'll do and do what you say.
Reply
#16
I have a generic Forstner bit set that I picked up years ago at Woodcraft. It has been fine for making shop fixtures and shop furniture.

For doing peppermills, I picked up a couple of sizes of Colt Maxicut Forstner bits. The 1-1/16" came as a set with an extension. I have been very happy with the Colt bits.
"the most important safety feature on any tool is the one between your ears." - Ken Vick

A wish for you all:  May you keep buying green bananas.
Reply
#17
(06-25-2018, 01:57 PM)DCM Wrote: I'd like to get a nice set of forstner bits so looking for advise. I have a cheap set & a few others, but want a better set. I understand there are different rim types that have +'s & -'s.
Thanks
David

Convalco ,was sold to Morris wood Tool company. Convalco was known s the premier source for Forstner bits. 
You can still buy Convalco on E-Bay. Or try the new company. I have 7 of their bits ,plus two sets of Grizzly Forstner bits. The 7 I bought are the ones used the most, pricey but worth the extra cost. The Grizzly bits are decent, like a Chevy compared to a Rolls Royce. 
mike
Reply
#18
Lee Valley HSS.  Excellent bits for a reasonable price.

Lee Valley HSS Forstner Bits
Still Learning,

Allan Hill
Reply
#19
I think I'll go for the Freud carbide bits. I'm willing to spend a bit more for longer life.
Thanks a bunch for the assistance
David
Reply
#20
(06-26-2018, 02:03 AM)mike4244 Wrote: Convalco ,was sold to Morris wood Tool company. Convalco was known s the premier source for Forstner bits. 
You can still buy Convalco on E-Bay. Or try the new company. I have 7 of their bits ,plus two sets of Grizzly Forstner bits. The 7 I bought are the ones used the most, pricey but worth the extra cost. The Grizzly bits are decent, like a Chevy compared to a Rolls Royce. 
mike


I have some Morris Wood Tool Forstners from my routerbits.com acquisition.  Larger sizes but should probably put them up for sale.
Reply


Forum Jump:


Users browsing this thread: 2 Guest(s)

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.