Posts: 12,197
Threads: 2
Joined: Nov 1999
Location: Nebraska City
05-16-2021, 12:24 PM
(This post was last modified: 05-16-2021, 12:27 PM by KC.)
Three of the 8 (?) hex drive screws that connect the rails to the saw top (and wings) will.not.budge. The five I did break loose took everything I had. The other 3 are rounded off enough now from the key slipping that I guess the rails are going to stay on it during the move.
With the extension table off, it's probably no biggie... but I took the Xacta saw apart four of 5 times and never had this problem. And since I put the SS together, I know I didn't put any extra gorilla on those screws.
Thanks for listening. I feel better now.
Posts: 1,998
Threads: 1
Joined: Aug 2016
(05-16-2021, 12:24 PM)KC Wrote: Three of the 8 (?) hex drive screws that connect the rails to the saw top (and wings) will.not.budge. The five I did break loose took everything I had. The other 3 are rounded off enough now from the key slipping that I guess the rails are going to stay on it during the move.
With the extension table off, it's probably no biggie... but I took the Xacta saw apart four of 5 times and never had this problem. And since I put the SS together, I know I didn't put any extra gorilla on those screws.
Thanks for listening. I feel better now.
Have you tried a 5mm hex bit in a impact driver ? May work. Roly
Posts: 12,197
Threads: 2
Joined: Nov 1999
Location: Nebraska City
(05-16-2021, 01:24 PM)Roly Wrote: Have you tried a 5mm hex bit in a impact driver ? May work. Roly
Rounded off just a bit too much for that at this point.
I did go the hex it socket/ratchet. Mess with it (them) too much before that, too.
Posts: 2,382
Threads: 0
Joined: Dec 2011
I'd use a grinder(cutting disc)/drill (if necessary) and remove the rounded bolts.
Simon
Posts: 14,850
Threads: 10
Joined: Jan 2010
Location: southeastern VA
(05-16-2021, 10:06 PM)Handplanesandmore Wrote: I'd use a grinder(cutting disc)/drill (if necessary) and remove the rounded bolts.
Simon
or use a left-hand drill bit in a reversible drill motor. One the size of the screw shaft ought to be about right.
Either it unscrews the screw for you or it removes the screw head.
You are going to have to replace those screws in the new shop anyway.
"the most important safety feature on any tool is the one between your ears." - Ken Vick
A wish for you all: May you keep buying green bananas.
Posts: 16,471
Threads: 0
Joined: Mar 2005
(05-16-2021, 12:24 PM)KC Wrote: Three of the 8 (?) hex drive screws that connect the rails to the saw top (and wings) will.not.budge. The five I did break loose took everything I had. The other 3 are rounded off enough now from the key slipping that I guess the rails are going to stay on it during the move.
With the extension table off, it's probably no biggie... but I took the Xacta saw apart four of 5 times and never had this problem. And since I put the SS together, I know I didn't put any extra gorilla on those screws.
Thanks for listening. I feel better now.
???
CTA Tools 9030 Fluted Screw Extractor Set, 5-Piece - - Amazon.com
---
See ya later,
Bill
Posts: 527
Threads: 0
Joined: Feb 2021
Location: Stevi, Montana
As mentioned above by Ivan, in conjunction with the left hand drill bit, you can drill a complete through hole to relieve some of the stress on the threads of the fastener.
Used that technique to remove stubborn fasteners on jet engines at times.
Posts: 12,604
Threads: 0
Joined: Aug 2003
Location: Wapakoneta, OH
I can only sympathize and suggest you find a method to get them out and replace them while the saw is apart. Curious as to why they are frozen, but that may just be an unsolvable puzzle.
I started with absolutely nothing. Now, thanks to years of hard work, careful planning, and perseverance, I find I still have most of it left.
Posts: 2,382
Threads: 0
Joined: Dec 2011
(05-17-2021, 07:40 AM)fredhargis Wrote: I can only sympathize and suggest you find a method to get them out and replace them while the saw is apart. Curious as to why they are frozen, but that may just be an unsolvable puzzle.
Since they haven't been over-tightened, rust?
Simon
Posts: 9,536
Threads: 0
Joined: Jan 2005
Location: Orlando FL
Can you get some vice grips on those bolts?
